[NEW] Cooper FlexArm Tablet Arm Mount – Desk Clamp Holder for iPad & Tablets up to 17″

CPR239BLK129_FBA

Color
Black
Shipping to . message

Set it at eye level. It stays there.

Holding a tablet gets tiring, and propping it on the desk means looking down all day. The Cooper FlexArm clamps to the edge of your desk and holds an iPad, tablet, e-reader or portable monitor at eye level, with both hands free. Two aluminum arms reach 23.6 in (60 cm) and hold up to 3.3 lb (1.5 kg). Tighten the joints with the included hex key and the arm stays where you set it.

Fits screens up to 17″ with an edge of 4.7–10 in (12–25 cm) for the holder to grip. Use a bare device or a slim case.


Hands-free, eye level: Cooper FlexArm clamped to a desk, holding a tablet at eye level for a video call
  • Reaches23.6 in60 cm
  • Holds up to3.3 lb1.5 kg
  • Fits screensUp to 17″Gripped edge 4.7–10 in (12–25 cm)
  • Desk clamp fitsUp to 3.5 in9 cm thick
  • Rotates360°Portrait to landscape
  • Joints3 tension jointsTighten with the hex key
One arm, more possibilities: FlexArm as a second screen next to a laptop, at the bedside and on a kitchen counter

The desk clamp also fits a bedside table or a kitchen counter, as long as the edge is flat and no thicker than 3.5 in (9 cm). Clamp it to the back edge and point the screen toward you. The base swivels 360°, so you can swing the arm out of the way and bring it back.

Engineered to hold 3.3 lb (1.5 kg): two 11.8 in (30 cm) arms, TensionSet joints, cable clips, padded holder jaws and a metal desk clamp for desks up to 3.5 in (9 cm); not for curved edges, round posts, pillar bed frames or padded headboards

The arms are aluminum. The desk clamp is metal, with a steel screw, a silicone top jaw and a rubber pad underneath, so it does not mark the desk. The joints are reinforced polymer with a steel tension screw inside. If a heavier tablet makes the arm droop, tighten the joints with the hex key in the box. If the arm feels too stiff, loosen them.

Works with iPads, Android and Windows tablets, e-readers and 15.6 to 17 inch portable monitors; fits devices 4.7–10 in (12–25 cm) across the gripped edges, up to 3.3 lb (1.5 kg)

A device fits if it passes three checks. The edge the holder grips measures 4.7–10 in (12–25 cm). It weighs 3.3 lb (1.5 kg) or less. And it is bare or in a slim case, because the jaws must close over the front of the screen. Rugged, bumper and keyboard cases do not fit.

Phones fit too, held lengthwise. Cut-outs on both sides of the holder let a charging cable reach the port while the device is mounted.

Portrait to landscape, 360 degree base swivel, 23.6 in (60 cm) reach and cable clips; not for curved edges, round posts, pillar bed frames or padded headboards

The holder sits on a ball joint. Turn the screen from portrait to landscape, or tilt it down toward you, without taking the device out. FlexArm is made to be set and left: the arm moves when you tap the screen, so it suits reading, watching and calls rather than drawing or writing with a stylus.

FlexArm vs a typical gooseneck arm: extra-wide fit up to 17 inch, TensionSet joints that don't sag, built-in cable clips, full-metal desk clamp

With the screen at eye level you look ahead instead of down, so there is less neck strain. For the steadiest hold, bend the arm into a Z shape rather than straight. With a heavier device, angle the middle joint back so both arms share the weight.

In the box: FlexArm two-section arm with metal desk clamp, tablet holder, hex wrench and manual in a zero-plastic kraft box
  • Two-section arm with the metal desk clamp attached
  • Tablet holder, spring-loaded, with steel pins
  • Hex key to set the joint tension
  • Instruction manual

Set up in five steps.

  1. Clamp it to the desk: on the back edge, up to 3.5 in (9 cm) thick. Turn the screw until the clamp is firm.
  2. Fit the holder: unscrew the cap, slide the holder onto the ball joint until it clicks, then tighten the cap.
  3. Insert the device: seat one side in the holder, pull the other side over the edge, and center it.
  4. Position the arm: bend it into a Z, bring the screen to eye level and turn it to portrait or landscape.
  5. Set the tension: if the arm droops or feels stiff, tighten or loosen the joints with the hex key.

Specifications.

Reach 23.6 in (60 cm), two 11.8 in (30 cm) arms
Holds up to 3.3 lb (1.5 kg)
Fits Screens up to 17 inch, with a gripped edge of 4.7–10 in (12–25 cm); bare devices and slim cases
Desk clamp Flat desk edges up to 3.5 in (9 cm) thick
Rotation Holder turns 360° on a ball joint and tilts down; base swivels 360°
Joints 3 tension joints, adjustable with the included hex key
Cables Clips along the arm; cut-outs on both sides of the holder
Material Aluminum arms; metal desk clamp with steel screw, silicone top jaw and rubber pad; reinforced polymer joints and holder with steel pins and spring
Weight 1.3 lb (578 g)
Color Black
Model CPR239

Questions.

What is the Cooper FlexArm?

The Cooper FlexArm is a tablet arm that clamps to the edge of a desk, bedside table or kitchen counter. It holds an iPad, tablet, e-reader or portable monitor at eye level, so your hands are free and you do not look down at the screen. It has two aluminum arms, three tension joints and a spring-loaded holder that turns from portrait to landscape.

How far does the FlexArm reach?

The FlexArm reaches 23.6 in (60 cm) from the desk clamp, with two arms of 11.8 in (30 cm) each. For the steadiest hold, bend the arm into a Z shape rather than holding it straight out. The base swivels 360°, so you can swing the screen across the desk or out of the way.

How much weight can the FlexArm hold? Will it sag?

The FlexArm holds devices up to 3.3 lb (1.5 kg). Its joints carry a steel tension screw, so the arm stays where you set it. If a heavier tablet makes the arm droop, tighten the joints with the hex key in the box until it holds. Devices over 3.3 lb (1.5 kg), such as laptops and heavy monitors, are too heavy.

Which iPads and tablets does the FlexArm fit? Will it hold a 13-inch iPad Pro?

Yes. The FlexArm fits every iPad, from the iPad mini to the iPad Pro 13, as well as Android and Windows tablets such as the Samsung Galaxy Tab and Microsoft Surface Pro 13. The rule is the edge the holder grips: it must measure 4.7–10 in (12–25 cm), and the device must weigh 3.3 lb (1.5 kg) or less. Use a bare device or a slim case.

Does the FlexArm work with portable monitors, Kindles and phones?

Yes. Portable monitors up to 17 inch, including 15.6 inch models, fit if the gripped edge is 10 in (25 cm) or less and the monitor weighs 3.3 lb (1.5 kg) or less. E-readers such as Kindle, Kindle Paperwhite and Kobo Clara fit, and phones fit held lengthwise. Writing tablets with a stylus are not a good match, because the arm moves when you press the screen.

Will my tablet case fit in the FlexArm holder?

A slim case fits; a rugged, bumper or keyboard case does not. The holder jaws must close over the front of the screen to hold the device safely. With a thick case the jaws only touch the sides, and the device can slip out.

What can I clamp the FlexArm to?

The desk clamp fits any flat edge up to 3.5 in (9 cm) thick, such as a desk, a bedside table or a kitchen counter. It does not fit curved edges, round posts, pillar bed frames or padded headboards. A silicone top jaw and a rubber pad underneath protect the surface, and no drilling is needed.

Does the FlexArm wobble when I tap the screen?

Yes, the arm moves when you tap or press the screen. The FlexArm is made to be set and left, for reading, watching, video calls and recipes. For drawing or writing with a stylus, use a stand that rests on the desk.

What is the FlexArm made of, and what if a joint gets loose?

The arms are aluminum, and the desk clamp is metal with a steel screw. The joints and the holder are reinforced polymer, with steel tension screws in the joints and steel pins and a spring in the holder. If a joint loosens over time, tighten it again with the included hex key.

How do I set up the FlexArm, and what is in the box?

Setup takes five steps: clamp the base to the back edge of the desk, fit the holder onto the ball joint, insert the device, bend the arm into a Z at eye level, and set the joint tension with the hex key. In the box: the two-section arm with the desk clamp, the tablet holder, the hex key and an instruction manual.